2 on Warm IR Patio Heater Parts

Sidel Series 2 infrared radiator

Fri, 03 Jul 2026 06:33:33 +0800

On the blow molding line, heating drift is the quiet killer. One radiator that’s not pulling its weight throws preform temperature off, and suddenly you’re chasing rejects—thin walls, crystallization, inconsistent stretch. The Sidel Series 2 infrared radiator is built to stop that drift at the source by matching OEM heating performance, pin for pin. What matters, technically We engineer the Sidel Series 2 infrared radiator to hit the 1:1 parameters mainstream blow molders expect—Sidel, Krones, SIPA, Husky, SACMI, and Nissei ASB. Typical units run 2300–2800 W, 230 V, with quartz tube lengths dialed in and standard R7s connectors so the lamp seats the same way in the heating tunnel. Short-wave infrared output gives you fast, surface-driven heating, and the filament geometry plus reflector alignment keep the beam pattern in the narrow band your preform neck and body need. The tolerances are tight enough that you can swap lamps without retuning the heating zones. Here’s why it works in stretch blow molding: cycle time is set by how fast the preform hits the right temperature profile. Get the wattage, voltage, and emitter length right, and the lamp delivers repeatable heat density across each zone. That means fewer temperature swings, less scrap, and more consistent bottle weight and clarity. Energy use stays in line because the lamp heats on demand and cools quickly, so you’re not wasting heat in the tunnel. And because the build matches OEM dimensions, installation is a straight replacement—no bracket fabrication, no rewiring. Matching specs is only half the story. The lamp needs a clean, reflective tunnel with good airflow; heavy dust or oxidized reflectors will force it to overwork and shorten its life. Also check voltage stability at the socket—line sag and loose contacts stress the filament early. Expect around 5,000 hours of service life under normal conditions, and keep spares on hand for planned changeouts. That way you’re not chasing heat mid-run.

Krones Contiform 2 heating lamp

Tue, 09 Jun 2026 02:40:28 +0800

On the blow molding line, the heating tunnel is where you win the cycle time game—or you don’t. Preforms running cool drag you into under-blow, stress cracks, and bottles that come off-weight. Run them too hot and you’re staring at crystallization and haze. The Krones Contiform 2 heating lamp sits right in the middle of that balancing act. If the emitter doesn’t match the machine’s thermal profile, you pay for it every shift—in scrap and in constant micro-adjustments. What actually matters is the match. Not just “it fits,” but output, geometry, and response. We build our Krones Contiform 2 heating lamp as a 1:1 parameter replacement against OEM baselines across the major blow molders—Krones, Sidel, SIPA, Husky, SACMI, and Nissei ASB. It’s a short-wave infrared halogen emitter with a quartz tube, rated at 2.5 kW at 230 V (other voltages available), and it uses a standard R7s connector. Dimensions are held to OEM tolerances, so it drops straight into the existing lamp holder and throws the energy where the preform needs it—without having to re-align the whole heating zone. Here’s why it matters: consistent preform heating stabilizes the stretch blow molding window. When infrared output stays steady and thermal response is repeatable, you get a tighter temperature spread across the neck and body, fewer hot spots, and less operator tinkering. That means fewer rejects, more uptime, and energy use that behaves predictably—because the lamp isn’t fighting the machine’s design. Installation is straightforward, but the heating tunnel is a harsh place. Keep the lamp aligned to the reflector, and make sure the terminals stay clean and tight. High current plus thermal cycling will find a weak connection fast. If your line runs high-barrier or heat-sensitive materials, double-check the spectral output against your preform resin—some grades are more sensitive than others. Treat the lamp like the precision component it is, and the Contiform 2 heating performance stays repeatable shift after shift.

Krones Ergomodul 2 heater lamp bulb

Wed, 03 Jun 2026 09:42:53 +0800

Run a Krones Ergomodul 2 and you already know the feeling: the whole heating cell is walking a tightrope. One lamp goes south, the tunnel profile drifts, and you watch output drop before you can even call maintenance. Then you get to chase down a replacement that fits—without forcing you to re-tune the entire line. What matters under the hood We built the Ergomodul 2 heater lamp as a direct-fit infrared emitter, spec’d to the machine: quartz envelope, halogen filament, and an R7s connector. It hits the voltage and wattage the heating tunnel wants, so the preform heating curve stays where it should. The filament geometry and reflector alignment are set to keep heat density consistent across the preform wall—exactly what you need for repeatable stretch and blow performance. Why this one stays in the machine With this lamp installed, the Ergomodul 2 keeps running its intended cycle instead of fighting temperature swings. Alarms quiet down, you do fewer manual interventions, and you stop paying for scrap from off-heat. Energy stays near baseline because the emitter matches the machine’s thermal design, and downtime shrinks because the swap is clean—drop it into the holder, no custom brackets, no rewiring. The shop-floor details The bulb is engineered for the Ergomodul 2, but it still needs clean contacts, proper alignment, and the right voltage. Handle it by the base, not the quartz tube, and check the holder during install. Oxidized terminals and bent contacts will kill it early—even with a good lamp.